Installing a medicine cabinet: recessed and surface-mount options
A medicine cabinet is one of the highest-impact upgrades you can make in an Australian bathroom. It hides clutter, adds storage above the basin and gives you somewhere to mount lighting. The decision that shapes the whole job is how the cabinet is fixed: recessed units disappear into the wall, while surface-mounted cabinets hang on the face of it. Both are well within reach of a competent weekend renovator, but they suit very different walls.
This guide walks through both methods, from measuring the cavity to sealing the edges, with the trade, tooling and building-standard realities of Australian bathrooms in mind. You'll find advice for fibro, brick veneer and tiled walls, notes on what to check before you drill into an older home, and the hardware that actually turns up at the trade counters of Bunnings and Mitre 10. The same rules apply whether you're in a Sydney terrace, a Queenslander in Brisbane or a modern apartment in Melbourne: measure carefully, fix into structure, and seal every wet edge.
Recessed or surface-mounted: what changes in your bathroom
The two options differ far less in appearance than people expect, but they differ hugely in what they demand of the wall. A recessed cabinet is built to sit inside a cavity, so its finished face sits almost flush with the plasterboard or tile. A surface-mounted cabinet is a box fixed onto the wall, and because it has to be deeper than the cavity behind the wall, it projects into the room.
Here is how the practical differences stack up.
| Feature | Recessed cabinet | Surface-mounted cabinet |
|---|---|---|
| Wall cavity | Needs a genuine cavity between studs, often with added noggings | None required; fixes to any flat wall |
| Typical depth | 90–120 mm, sits nearly flush | 150–200 mm, protrudes past the wall face |
| Best suited to | New builds, full renovations, walk-in showers | Brick veneer, concrete, tiled walls, rentals |
| Wall disruption | Cutting, framing and patching | Minimal; two or three fixing points |
| Effect on space | Frees up elbow room at the basin | Reduces clearance in front of the vanity |
| Install time | Half a day to a full day | Two to three hours |
| Cost and reversibility | Costlier if the wall is brick or masonry | Cheaper and easy to remove |
Recessed wins in tight bathrooms and anywhere the vanity has been pushed hard against a wall, because the cabinet doesn't eat into the space you stand in. Surface-mounted wins in older brick veneer, in rental properties where cutting walls is off the table, and on walls already tiled floor to ceiling — cutting into a tiled shower wall is a job most people would rather avoid. In humid climates such as Brisbane or coastal Queensland, a recessed cabinet also keeps storage away from condensation collecting on the wall face, provided the cavity behind it stays ventilated.
Measure the wall before you cut anything
Start with the cabinet, not the wall. Measure the actual unit: widths of 900 mm, 1200 mm and 1500 mm are common in Australian ranges, and mirrored doors add a millimetre or two to the frame. Recessed bodies usually run 90 to 120 mm deep, which tells you straight away whether your wall can take it.
Australian timber framing generally uses 90 x 45 mm studs at 450 mm or 600 mm centres, so the clear cavity between studs is only about 45 to 80 mm. If the cabinet is deeper than that, it needs to sit in a thicker framed wall, drop into a service cavity, or be built out locally around the unit — which rather defeats the purpose. Check for noggings and plumbing before you commit to a width, because a 900 mm cabinet may straddle a stud and wet walls often carry the basin's waste pipe. If any excavation or landscaping is happening nearby, call 1100 to have underground services marked before the trade starts.
Work out the height too. A cabinet over the basin usually has its bottom edge 200 to 300 mm above the benchtop, and sits roughly 900 to 1200 mm above the floor for adults, though taller households in 2.7 m ceiling new builds can go higher. In homes built before the mid-1980s, check what the wall is made of first: asbestos cement sheeting appeared on some fibro homes of the 1960s and 70s, and drilling into it without identifying the material can release fibres, so get the wall checked before you start.
Installing a recessed cabinet
Once the opening is marked, keep it level with a laser or a spirit level, cut the plasterboard with a utility knife, then trim the stud faces with a reciprocating saw or multi-tool. In brick veneer or masonry, use an angle grinder with a masonry disc or a hole saw, working slowly and cooling the bit, because brick veneer cracks along odd lines that are hard to hide behind a cabinet. Plan the cut so it lands on a tile joint rather than across the middle of a tile.
Framing the opening is the part people rush. Add a timber nogg ing or header above the unit so the cabinet's weight hangs on structure rather than on the edge of the plasterboard, and use treated timber or steel framing in any wall that gets wet. Screw the cabinet flange into the studs, check the unit is genuinely plumb, and only then tighten everything down.
Wet areas need extra care. Under AS 3740, wet-area walls and floors must be waterproofed, and a cabinet sitting in the splash zone should not have its back in standing water. Seal the perimeter with a flexible silicone or the manufacturer's sealing strip, and keep the wall cavity ventilated rather than sealed airtight, or you trap moisture inside the wall. In Queensland and northern NSW, check the cavity for possum nests before closing it up, and fit a one-way vent where animals have been living.
Fitting a surface-mounted cabinet
Surface mounting looks simple, but the details decide whether it looks professional. The back of the cabinet must sit on a flat, even wall. Old tiled walls often undulate and brick veneer moves, so shim the unit with a timber batten or packers screwed back to the studs, then fill the gap between cabinet and wall with silicone or grout.
Fixings depend on the wall. Into timber studs, drive screws straight into the studs rather than relying on plasterboard anchors alone for a heavy cabinet. Into brick veneer, use masonry screws or a chemical anchor; into concrete, a masonry screw and the right drill. Into plasterboard only, use cavity anchors rated well above the cabinet's weight, and always pre-drill so you don't blow out the face of a tile. Keep the cabinet clear of the shower screen's swing path, and remember that a 180 mm deep cabinet projects well past a 100 mm vanity.
Check what runs behind the wall before you drill, because a copper pipe, shower hose or water line can turn a two-hour job into a flooded bathroom. If you plan to add a socket or LED strip inside the cabinet, the wiring has to meet the current electrical installation rules, and in most states bathroom lighting must sit in a suitable wet-rated zone. Battery or 12 V strips avoid the issue entirely; mains work belongs with a licensed electrician.
The hardware run: what to buy before you start
Most renovators get everything in one trip, and a few choices are worth thinking about before you pay for it.
- A mirrored cabinet in a width that actually fits your cavity — 900 mm for a single basin, 1200 to 1500 mm for a double vanity.
- LED strip lighting, either 12 V or battery powered, if you'd rather not call an electrician for a light.
- Mould-resistant silicone in a colour that matches the grout and wall paint.
- Masonry screws and chemical anchors for brick veneer or concrete, plus cavity anchors as a backup.
- A multi-tool, a masonry disc for the grinder and a reliable stud finder.
- Spare tiles and matching grout, in case the cut for a recessed unit lands badly.
- A dust mask, eye protection and ear protection, because grinding in a small tiled room is unpleasant.
Renovators swap cut lists, fixing advice and cabinet dimensions freely before they shop, and browsing shared project advice ahead of your trade counter visit is a quick way to learn which cabinet sizes genuinely fit Australian cavities and what fixings others have used on brick veneer. Trade counters at Bunnings and Mitre 10 will have mirrored units in the common widths, handle finishes from satin chrome to matte black, and adjustable glass shelves, with prices rising as width, depth and lighting go up.
Finishing details and your next project
Stand back before the silicone cures and check the cabinet for level, plumb and even gaps on all sides. Fill the perimeter with good-quality mould-resistant silicone, and let it cure for at least 24 hours before the area gets wet. Clean the grout lines and wipe the mirror down, because a streak-free finish is what people actually notice once the job is done.
Ventilation matters more here than the cabinet itself. Running an exhaust fan during and after showers keeps condensation off the mirror and stops black mould forming in silicone and grout, which is a common sight in humid Queensland and Northern Territory bathrooms. A recessed cabinet with a mirrored back and sealed glass door holds dust and moisture far better than an open shelf, and in Perth's bright summer light a mirrored door doubles as a window.
If you're turning this into a larger weekend project, plenty of people tackle an outdoor refresh in the same diary. Taking a look at deck railing ideas for styles that suit the house, then matching the cabinet's handle finish to the outdoor hardware, gives the whole place a consistent look. So pick the cabinet size at the trade counter, confirm your wall type and cavity depth, gather the fixings, and book Saturday morning — measure twice, cut once, and the medicine cabinet will look like it was always part of the bathroom.